Super Jerry Base Finished

So well the base for the Super Jerry is done, cutting the WIP a little short, but I was on a roll putting the paint, washes and pigments on the thing that I didn't want to pause to set the thing up for pics...

Anyway. I glued all the concrete debris on with white glue and gave it all a base coat of Tamiya Buff colour after the glue had dried. Also added some little rocks here and there.

Than I gave the cracks in the pavement a quick pin wash using the black ready made wash by Vallejo. Then I added some streaking and washes with a "European Dirt" of the same brand.
Also added some oil streaking particularly the rust effects and when that had dried a mix of light gray and light (very light) moss-green pigments.

After that I glued in the grass which I made from the hairs from an old paint brush (pig's hair I think). I used super glue to glue them into little tufts and then, after giving them a quick hint of drab green, used PVA (white) glue to stick then into the crack and holes in the pavement.

Than put the model on the base using copper rods, which were SG'ed into the feet and then gave the whole thing another treatment with pigments to blend  it all together a little...

Hope you like the result.

Cheers!

Super Jerry Base

A few months ago I finished work on a Super Jerry and it's been just standing there.. so I decided to build it a base.
I wanted it to be an urban environment as I think it suits the paint scheme. I also wanted to keep it kind of simple as the thing itself is busy looking enough...

Anyway here the breakdown so far:
First I build up the core by glueing polystyrene sheets on a piece of chipboard of 15cm square using wood glue.
The tiles on the sidewalk are 2mm thing pieces and the broken pillar is a piece of street chalk I stole from my 4 year old, snapped it in half and drilled some holes into them piece for the 1mm copper wire to go through. This is a dry-fit.

For the tarmac I used a piece of cracked and torn 80 grit sandpaper, also glued in place using wood glue (white glue basically).
I then built up the sides with 1.5 mm thick styrene plate (plaplate to some).

Sprayed it with gray Tamiya primer:

After then putting a few layers of Tamiya black on the sides and covering that with glossy clear coat, I masked the sides off.
I then put a coat of black primer on the top. Not that it needed more primer but I still have a can of Vallejo primer I'm using as paint because as primer I really don't like it... better use it I thought.

 Then I put a little dark gray on the tarmac from a can of Tamiya German grey I had left.. just a light dusting. Also airbrushed the sidewalk and the pillar and some debris.
After I painted the stripe on the tarmac I glued all the pieces in place with white glue and added some small rocks and a little sand here and there.

 Here's how the Jerry will stand on the thing.

Next up there's more painting of details. Some washes, streaking/water marks/dirt and some pigments... stay tuned.

Cheers!

Auricom Griffon base

So... I've been making some more progress on that base. It's slow going, but going.

I filled up the whole thing using acrylic filler mixed with sand and rubbed some chalk on it to change up the texture here and there. I want the track to look quite rough... in the game this thing is based on there's a lot of exploding vehicles and stuff. I want to show some of that violence. I'll working on bit of debris and wreckage from some of the losers...

Also scratched some reinforced concrete slabs for the deck bit at the top. 

Then I painted the sides black and masked them off after a couple of clear coats.. put primer on the rest and masked off the track's stripe pattern.

Painted on some Tamiya flat yellow with a brush and that's about it...

It still looks kind of dinky right now... but it will get some washes and pigments and I'm hoping this will pull it all together somewhat. Fingers crossed.

Auricom Griffon Base Restart...

After looking at this thing for a while I realized, I needed to soalve the problem of the model twisting on the base...

I got a tip on one of the forums I frequent about using square tube to attach the model to the base (feeling stupid for not thinking of that myself)... I decided to double back a little bit and ready some of the base. 

I ripped out most of the polystyrene sheets and put in a square bit of styrene tube. I found some metal bar (i think it's pyrite) that fits it perfectly. I attached the tube into the base exactly like I had done with the round tube (using poly clay and plaster)..

In building up the further layers of polystyrene I glued in bits of plastic card that fit around the tube. So bits of card with square holes in them, glued to the tube with SG and to the polystyrene with wood glue (about the same as white glue I think).

This was done to make sure it wouldn't move under the weight of the model.

The bottom of the Griffon now had a gaping 4mm hole in it... so I made it bigger. Put in a piece of the same square tube that went all the way to the 'ceiling' inside the Griffon. Then I fixed it in place at the hole with SG and green stuff and on the inside by using a thin wooden stick to push a ball of GreenStuff all the way up into the tube and stick it to the ceiling on the inside of the tube... hope that makes sense. Anyway it's in there solid.

I put a little weld seem and some bolts on the tube end sticking out and painted it (also put some greebly on the top of previously failed attempts at fixing the model to the base)...

With that done I started putting some filler on the base. I used acrylic filler (which I think is basically thick unpigmented acrylic paint) and mixed it with cat litter.... a total experiment as I had never worked with the stuff. 

Well the cat litter absorbed a lot of moisture from the filler quite fast, making it quite difficult to spread out... it also shrank quite a bit as it dried. 

So, not really what I expected but really good to know (if I ever want to make a rocky dried up desert base..). 

I'll just cake on another layer of the filler mixed with something non-absorbent. Something that will give it a more asphalt structure too.

Then I did a quick dry-fit of the model on the base.. it looks like it just might work. 

Thanks for looking, let me know what you think!

Auricom Griffon Base Build

Been working on the base. I had a design and based on that I drew a template, printed it out and used that to build a cardboard model... I had a pic of that but the SD card got corrupted (yes it does corrupt data when you just rip it out of your machine ahah).

Anyway here the template:

When I saw how that worked I used the cardboard to cut some 1.5 mm thick styrene sheet to size and built the walls around a pressed wood base (not sure what the english is for this type of wood product).

After this I started thinking about how I was going to fix the model to the base... I want it to hover over the base under an angle and that turned out to be a bit of a ball ache. The model is quite a bit heavier than I thought.

the first attempt was to drill and glue in two 2mm pieces of copper rod into the bottom, but that wasnt' strong enough and I couldn't secure them into the mainly styrofoam base... the second attempt was to get a long bit of threaded bar (4 mm thick) but that the nut I glued into the bottom of the model didn't hold. I used green stuff and SG but to no avail. beside it woul dhave cause problems when putting the model on the base I there most likely would not have been enough room for the thing to turn enough times to get it close enough to the base...

Anyway nou I've put in a piece of styrene tube (inner circumference of 4mm) and I'm going to glue in a piece transparent styrene rod into the model and then when the base is finished but glue the rod into the tube... fingers crossed.

Cut out a square block out of the base layer of styrofoam. stuck it in place with a lump of milliput and filled in the hole with plaster. I will further secure it later by glueing a pieve of styrene sheet with a hole in it over the square hole (havein the tube stick through). 

Then I'll build up the rest of the base with more layers of styrofoam and fill up all the holes with that acrylic filler stuff

Lot of talk, not much to see.

More exciting posts later.

Auricom Griffon Base Design

This thing will be going onto a base. I want it in flight, so I don't really have any other option that to build it a base.
This will my first ever base, so the build will most likely be a nightmare.

Anyway this is the design for it. Modeled after a WipeOut racetrack... a segment thereof.